I like this paper it's good quality and very easy to use- I bought it intending to use it for polymer clay. I wanted to make my own transfers but you can't cut through it with a clay cutter. It works as intended and described- just make sure you cut it to size before applying.

Using this for scale modeling. Making custom size numbers for vehicles and aircraft work great. To eliminate waste, create paper samples to ensure proper size. Once done, use that size one this decal sheet. Maintain a file of what you are making. Use thus file for your next project so you can utilize this sheet again without wasting material.

This waterslide paper was easy to use ( I purchased the laser printer version) and I did not have to spray a clear coat before submerging it in warm water. I applied this to my fuel tank.

I was asked to paint birch trees on a set of planters. No problem, except I found out that I suck at painting tiny birch trees. So I opted for waterslide decals of birch trees, and they came out like I envisioned! Super super easy to do. The results were stunning... that is, for birch trees on planters. When dry, you'd be hard-pressed to even find the edges of the decal. They were kinda stretchy when applying them, and didn't tear like I was fraid they might.Amazing stuff, and again - so easy to use!

Product works well, works better if you can cut the exact image out with no access but great product

LOVE IT CAN'T BELIEVE IT WORKS SO GOOD!!!! THANKS FOR A WONDERFUL PRODUCT!!!

What a fun item to have! I have not used this in my laser printer yet, but I made some Halloween decals of my own for my nails on the CLEAR laser printer decal waterslide paper. It worked great! This was a first try for me, so there's a learning curve. Here's how I did it, if you're interested. Hope this helps! I cut off a small piece, painted some cheerful Halloween ghosts on it, (based on something found online) with acrylic paint, and let dry. I sealed it with clear nail polish and let dry. I trimmed it closely. Next time, I will not cut between the ghosts as spacing was compromised when I applied it. This was my fault, not the paper's. I only had to put the tiny decal in water for a few seconds, then it was ready start sliding off the paper with pressure applied. If you watch the backing, you can readily see when it's all wet. Positioning carefully, slide it directly off the backing paper onto your dry prepped nail (basecoat & color) and press firmly into place. I used tweezers to assist with this. Let dry and embelish around the decal if desired (I did with dotted stars). Let dry. Topcoat with clear polish (fyi: none of my polishes are gel.) I needed to create my own because I can directly paint onto my left hand, but not my right. With my short fingernails, this lets my creativity fly!When I have time, I'll start collecting little sketches to print that could be applied with just the black line drawing, or I could print, paint, and then apply them. (My laser printer only prints in black.) This is going to be fun to use! Now I'm thinking about embellishing - even monogramming - stainless steel mugs, suitcases, candles...

Excelente calidad!!

Product came very fast. Bought this product because the inkjet version of waterslide I bought from a different maker would not work in my printer. This printed very well on Canon Laser printer with no problems. Colours were very vibrant on paper. Very easy to use and backing came off without fighting it. Was able to lay my design onto a wine glass and get the wrinkles out without any issue. Although I bought clear paper you can still see the edges of the paper on your glass. My second design I cut closer to the art work so it would not be as noticeable. I would do a precise cut on my art work next time. Would recommend this product and vendor.

Die Wasserschiebefolie lässt sich gut bedrucken und weiter verarbeiten. Nutze sie für Kerzen und komme damit sehr gut zurecht.Meine Drucker zieht das Blatt ohne Probleme durch. Farben leuchten. Alles super!

me gusto mucho la calidad y el servico que me dieron fue super rapidisimo y como lo queria para un regalo todo salio perfecto les doy un 10!!!!!!!!!!!!!!!!!!!

This is a really great decal paper; I don’t have a laser printer myself but I really like the quality of laser prints so I take the paper to my local library and put it in their laser printer. I’ve made decals to put on face plates of custom figures so my decals are *very* tiny and they can be quite hard to put in place- you basically get one try to put it on in a way that it will stick; if you reposition it at all, it loses much of its stickiness and you must rely on a good sealant spray to hold it in place (this is just my experience with tiny decals; larger ones may be easier to work with in this regard). I also recommend getting a sealing spray as it not only holds the decals with an extra measure of security but can help match your decal’s sheen to the rest of your project. The shininess of my decals on the matte vinyl face plates was very apparent so I applied a matte sealer (Mr. Super Clear UV Cut Flat spray) and after two coats, it was nearly impossible to tell the facial features were a decal at all as they were precisely the same sheen as the rest of the face and the decal edges were invisible, perfectly blended in to the rest of the face plate. Get this paper and a good sealer and you can decal anything!

Se despega fácilmente, no se adhieren bien al plástico

I like this paper it's good quality and very easy to use- I bought it intending to use it for polymer clay. I wanted to make my own transfers but you can't cut through it with a clay cutter. It works as intended and described- just make sure you cut it to size before applying.

Product works well, works better if you can cut the exact image out with no access but great product

This waterslide paper was easy to use ( I purchased the laser printer version) and I did not have to spray a clear coat before submerging it in warm water. I applied this to my fuel tank.

This is a really great decal paper; I don’t have a laser printer myself but I really like the quality of laser prints so I take the paper to my local library and put it in their laser printer. I’ve made decals to put on face plates of custom figures so my decals are *very* tiny and they can be quite hard to put in place- you basically get one try to put it on in a way that it will stick; if you reposition it at all, it loses much of its stickiness and you must rely on a good sealant spray to hold it in place (this is just my experience with tiny decals; larger ones may be easier to work with in this regard). I also recommend getting a sealing spray as it not only holds the decals with an extra measure of security but can help match your decal’s sheen to the rest of your project. The shininess of my decals on the matte vinyl face plates was very apparent so I applied a matte sealer (Mr. Super Clear UV Cut Flat spray) and after two coats, it was nearly impossible to tell the facial features were a decal at all as they were precisely the same sheen as the rest of the face and the decal edges were invisible, perfectly blended in to the rest of the face plate. Get this paper and a good sealer and you can decal anything!

I was asked to paint birch trees on a set of planters. No problem, except I found out that I suck at painting tiny birch trees. So I opted for waterslide decals of birch trees, and they came out like I envisioned! Super super easy to do. The results were stunning... that is, for birch trees on planters. When dry, you'd be hard-pressed to even find the edges of the decal. They were kinda stretchy when applying them, and didn't tear like I was fraid they might.Amazing stuff, and again - so easy to use!

Using this for scale modeling. Making custom size numbers for vehicles and aircraft work great. To eliminate waste, create paper samples to ensure proper size. Once done, use that size one this decal sheet. Maintain a file of what you are making. Use thus file for your next project so you can utilize this sheet again without wasting material.

LOVE IT CAN'T BELIEVE IT WORKS SO GOOD!!!! THANKS FOR A WONDERFUL PRODUCT!!!

Before buying I did some research on what to do reading all thr reviews deciding on this one. I was looking for something to just do outline to layer over glitter to make my tumblers pop. And boy did this do it. I used an epson work force inkjet printer. Some tips would be make sure after printing you spray it with a clear top coat, so you don't run the risk of the ink coming off. I did go with a glossy spray paint but found that when I go to epoxy seal it, it slides all over and leaves spots bare. I will be trying a matte or satin finish and will update my review at a later time. Also when you go to wet it be ready for it to curl onto itself before it straightens back out. As it's in the water I slide it off the paper just a bit and then apply it to my project to slide it off the rest of the way. Keep it wet til you get it in the desired location and you can begin to squeeze the water from under the decal for the permanent spot. Hi resolution images is best to ensure you get the quality that you want. Lower resolutions tend to come out fuzzy and or pixilated. I am happy with the over all outcome of both my projects even in the trial and error stage.

Excelente calidad!!

Product came very fast. Bought this product because the inkjet version of waterslide I bought from a different maker would not work in my printer. This printed very well on Canon Laser printer with no problems. Colours were very vibrant on paper. Very easy to use and backing came off without fighting it. Was able to lay my design onto a wine glass and get the wrinkles out without any issue. Although I bought clear paper you can still see the edges of the paper on your glass. My second design I cut closer to the art work so it would not be as noticeable. I would do a precise cut on my art work next time. Would recommend this product and vendor.

Die Wasserschiebefolie lässt sich gut bedrucken und weiter verarbeiten. Nutze sie für Kerzen und komme damit sehr gut zurecht.Meine Drucker zieht das Blatt ohne Probleme durch. Farben leuchten. Alles super!

me gusto mucho la calidad y el servico que me dieron fue super rapidisimo y como lo queria para un regalo todo salio perfecto les doy un 10!!!!!!!!!!!!!!!!!!!

Se despega fácilmente, no se adhieren bien al plástico

I like this paper it's good quality and very easy to use- I bought it intending to use it for polymer clay. I wanted to make my own transfers but you can't cut through it with a clay cutter. It works as intended and described- just make sure you cut it to size before applying.

Using this for scale modeling. Making custom size numbers for vehicles and aircraft work great. To eliminate waste, create paper samples to ensure proper size. Once done, use that size one this decal sheet. Maintain a file of what you are making. Use thus file for your next project so you can utilize this sheet again without wasting material.

This waterslide paper was easy to use ( I purchased the laser printer version) and I did not have to spray a clear coat before submerging it in warm water. I applied this to my fuel tank.

This is a really great decal paper; I don’t have a laser printer myself but I really like the quality of laser prints so I take the paper to my local library and put it in their laser printer. I’ve made decals to put on face plates of custom figures so my decals are *very* tiny and they can be quite hard to put in place- you basically get one try to put it on in a way that it will stick; if you reposition it at all, it loses much of its stickiness and you must rely on a good sealant spray to hold it in place (this is just my experience with tiny decals; larger ones may be easier to work with in this regard). I also recommend getting a sealing spray as it not only holds the decals with an extra measure of security but can help match your decal’s sheen to the rest of your project. The shininess of my decals on the matte vinyl face plates was very apparent so I applied a matte sealer (Mr. Super Clear UV Cut Flat spray) and after two coats, it was nearly impossible to tell the facial features were a decal at all as they were precisely the same sheen as the rest of the face and the decal edges were invisible, perfectly blended in to the rest of the face plate. Get this paper and a good sealer and you can decal anything!

 I was asked to paint birch trees on a set of planters. No problem, except I found out that I suck at painting tiny birch trees. So I opted for waterslide decals of birch trees, and they came out like I envisioned! Super super easy to do. The results were stunning... that is, for birch trees on planters. When dry, you'd be hard-pressed to even find the edges of the decal. They were kinda stretchy when applying them, and didn't tear like I was fraid they might.Amazing stuff, and again - so easy to use!

Product works well, works better if you can cut the exact image out with no access but great product

LOVE IT CAN'T BELIEVE IT WORKS SO GOOD!!!! THANKS FOR A WONDERFUL PRODUCT!!!

What a fun item to have! I have not used this in my laser printer yet, but I made some Halloween decals of my own for my nails on the CLEAR laser printer decal waterslide paper. It worked great! This was a first try for me, so there's a learning curve. Here's how I did it, if you're interested. Hope this helps! I cut off a small piece, painted some cheerful Halloween ghosts on it, (based on something found online) with acrylic paint, and let dry. I sealed it with clear nail polish and let dry. I trimmed it closely. Next time, I will not cut between the ghosts as spacing was compromised when I applied it. This was my fault, not the paper's. I only had to put the tiny decal in water for a few seconds, then it was ready start sliding off the paper with pressure applied. If you watch the backing, you can readily see when it's all wet. Positioning carefully, slide it directly off the backing paper onto your dry prepped nail (basecoat & color) and press firmly into place. I used tweezers to assist with this. Let dry and embelish around the decal if desired (I did with dotted stars). Let dry. Topcoat with clear polish (fyi: none of my polishes are gel.) I needed to create my own because I can directly paint onto my left hand, but not my right. With my short fingernails, this lets my creativity fly!When I have time, I'll start collecting little sketches to print that could be applied with just the black line drawing, or I could print, paint, and then apply them. (My laser printer only prints in black.) This is going to be fun to use! Now I'm thinking about embellishing - even monogramming - stainless steel mugs, suitcases, candles...

Excelente calidad!!

Product came very fast. Bought this product because the inkjet version of waterslide I bought from a different maker would not work in my printer. This printed very well on Canon Laser printer with no problems. Colours were very vibrant on paper. Very easy to use and backing came off without fighting it. Was able to lay my design onto a wine glass and get the wrinkles out without any issue. Although I bought clear paper you can still see the edges of the paper on your glass. My second design I cut closer to the art work so it would not be as noticeable. I would do a precise cut on my art work next time. Would recommend this product and vendor.

Die Wasserschiebefolie lässt sich gut bedrucken und weiter verarbeiten. Nutze sie für Kerzen und komme damit sehr gut zurecht.Meine Drucker zieht das Blatt ohne Probleme durch. Farben leuchten. Alles super!

me gusto mucho la calidad y el servico que me dieron fue super rapidisimo y como lo queria para un regalo todo salio perfecto les doy un 10!!!!!!!!!!!!!!!!!!!

Se despega fácilmente, no se adhieren bien al plástico